Разлики

Тук са показани разликите между избраната и текущата версия на страницата.

--- en:buttons_relays_and_programs [2023/05/20 07:54] – [Setting the buttons] siyana
+++ en:buttons_relays_and_programs [2023/09/22 09:56] (текуща) – svilen
@@ Ред 1: / Ред 1: @@
-=====Buttons, exits and programs=====
+=====Buttons, outputs and programs=====
-The controllers' work could be divided into two groups: governing where is set at which button which relays should be switched on and off and visualizing where are set the names of the programs and their duration.
+The controller work could be divided into two groups: controlling - where is set at which button which relays should be triggered and visualizing - where are set the names of the programs and their duration.
 {{ ::cwcontroller_buttons_relays.png?nolink |}}
 ==== Setting the buttons====
-The controller maintains up to 16 different programs. Depending on the given signal or combination of signals it is chosen the relevant program. The entrances for buttons are 6 and for the maintenance of more than 6 programs is needed the use of a combination of entrances, by separation diodes -  look  [[електрическо свързване#бутони|Electrical connection]].
+The controller maintains up to 16 different programs. Depending on the given signal or combination of signals it is chosen the relevant program. The inputs for the buttons are 6 and for the maintenance of more than 6 programs is needed the use of a combination of inputs, by separation diodes - look  [[en:electrical_connections#buttons|Electrical connection]].
 Setting the signals from the buttons to the corresponding program is done from the "Buttons and Relays" group, by setting the corresponding combination of "Input lines" for each group.
-====Governing of the relays====
+====Control of the relays====
-For each program, it is adjusted the state in which the six controlling relays should be. In the simplest control option, only the field "Relays on" is set, selecting one or a combination of several relays.
+For each program, is adjusted the state in which the six controlling relays should be. In the simplest control option, only the field "Relays on" is set, selecting one or a combination of several relays.
 Example 1: program 1 - relay 1, program 2 - relay 2, program 3 - relay 3.\\
 Example 2: program 1 - relay 1, program 2 - relay 1+2, program 3 - relay 1+3, program 4 - relay 1+3+4.
@@ Ред 19: / Ред 19: @@
 ====Visualization====
-The group "Outlook - work" consists of 16 subgroups presenting each program on the screen. The selection of the running group does not happen by pushing a button but with the state of the output relays. This is done to adequately reflect the different states and when using functions such as "Relays keeping their state" and [[Outputs controlled by time]].
+The group "View - work" consists of 16 subgroups presenting each program on the screen. The selection of the running group does not happen by pushing a button but with the state of the output relays. This is done to adequately reflect the different states and when using functions such as "Relays keeping their state" and [[Outputs controlled by time]].
 Each group is identified by the "Relay Status" setting. It is also assigned a name to be displayed on the screen as well as colors for the remaining time sector in the stopwatch view. Additionally, individual counseling time can be set for a credit of 100 cents. At zero time, it is used, the total "Time per Coin". For more details on timings, look at [[Individual program times]].
-====Допълнителни настройки====
-**Бутони - нормално затворени входове**\\
-Някой бутони, като например тези за пауза, са с нормално затворени контакт. За да може те да бъдат отчитани в момента на натискането им, а не при отпускането е необходимо да бъдат отразени в тази настройка.
-**Релета - нормално затворени изходи**\\
+====Extra settings ====
-От тук може да бъде обърната работата на някое от релетата. При неактивно състояние да е включено, а при активно - изключено.
+**Buttons - normally closed inputs**\\
+Some buttons, for instance, those for pause, are normally with closed contact. For them to be read simultaneously with their pressing and not upon release this setting is required.
-**Релета - първоначално състояние**\\
+**Relays - normally closed outputs**\\
-Положение на релета при поставяне на монета. Тук може да бъде зададен режим в който веднага да тръгне машината. Или например да бъде включено допълнително оборудване - например осветление.
+From here the work for one of the relays could be reversed. It could be turned on during the inactive state and turned off during the active state.
-**Изчакване за превключване на реле**\\
+**Relays - startup state**\\
-При превключване от един режим към друг, първо всички релета свързани с новия режим се поставят в неактивно състояние. Изчаква се зададеното време и се активира новото с
+The position of the relays when a coin is inserted. Here you can set a mode in which the machine starts immediately or for example to be set an extra piece of equipment - for example lights
+**Delay to switch the relays**\\
+When switching from one mode to another, all the relays connected to the new mode are set in an inactive mode beforehand. Activate the new mode after the time is up.