Разлики

Тук са показани разликите между избраната и текущата версия на страницата.

--- en:electrical_connections [2023/05/07 13:41] – siyana
+++ en:electrical_connections [2023/05/08 11:34] (текуща) – svilen
@@ Ред 1: / Ред 1: @@
 =====Electrical connection=====
-The controller CW01R66 consists of two circuit boards connected by a ribbon cable. The control board with a display, which is an inseparable part of the board, is intended to be placed on the front panel of the dashboard. The coin mechanism and all buttons are connected to it. The relay board could be placed at the base of the board as it is connected to the power supply and the control signals.
+The controller CW01R66 consists of two circuit boards connected by a ribbon cable. The control board with a display, which is an inseparable part of the board, is intended to be placed on the front panel. The coin mechanism and all buttons are connected to it. The relay board could be placed at the base of the case as it is connected to the power supply and the control signals.
 {{ :wiki:cw01r66_electrical_diagram.jpg?nolink |}}
@@ Ред 8: / Ред 8: @@
 ====Control signals====
-For control of the executive mechanisms such as pumps, valves, dispensers, and heaters are provided 6 relays as the contact circuit of each relay is shown on the labels. For each program could be made a random combination of active relays.
+For control of the executive mechanisms such as pumps, valves, dispensers, and heaters are provided 6 relays and the contact circuit of each relay is connected to the terminals. For each program could be made a arbitarty combination of active relays.
 {{ ::cw01r66_relays_diagram.png?nolink |}}
 The maximum permissible load on each relay is 250V 5A.
-**Tip:** To reduce the number of connected cables, power can be supplied to each pin and so when the free edge output is activated a control voltage will be directly available.
+**Tip:** To reduce the number of connected cables, a supply voltage can be provided to each relay and when it is activated a control voltage will be directly available.
 {{ :cw01r66_relays_common_power.png?nolink |}}
 ====Coin mechanism====
-The communication with the coin mechanism is done over the standard parallel interface, using connectors with 2 x 5 pins. You can make a consultation with the documents of the coin mechanism to check if it matches the drawing.
+The communication with the coin mechanism is done over the standard parallel interface, using connectors with 2 x 5 pins. You can reference the documents of the coin mechanism to check if it matches the drawing.
 {{ ::cw01r66_coins_acceptor_pinout.png?nolink |}}
 ^ outlet ^ name  ^ description ^
@@ Ред 24: / Ред 24: @@
 | 4 | COIN 6 | Impulse for a coin with code 6 |
 | 5 | RET | Returned coin / Impulse for a coin with code 7 |
-| 6 | INH | Prohibition for acceptance of coin |
+| 6 | INH | Inhibit of coins acceptance |
 | 7 | COIN 1 | Impulse for a coin with code 1 |
 | 8 | COIN 2 | Impulse for a coin with code 2 |
@@ Ред 30: / Ред 30: @@
 | 10 | COIN 4 | Impulse for a coin with code 4 |
 The controller is capable of recognizing the listed signals:
-  * единичен импулс на всеки един от 6-те канала - така се подържат до 6 различни типа монети
+  * single pulse for each of the 6 channels - this is how are maintained up to 6 different types of coins
-  * поредица от импулси, например 1 импулс - 50 ст., 2 имп. - 1 лев, 4 имп. - 2 лева
+  * a sequence of pulses; for instance 1 pulse - 50 cents, 2 pulses - 1 euro, 4 pulses - 2 euros
-  * импулси с различна продължителност, например 100 мс. - 50 ст., 200 мс. - 1 лев, 300 мс. - 2 лева
+  * pulses with different duration; for instance 100 ms. - 50 cents, 200 ms. - 1 euro, 300 ms. - 2 euros
-  * комбинация от кодове (известен като binary), например импулс едновременно 1 и 2 канал - така се подържат над 16 различни монети
+  * a combination of codes (known as binary); for instance pulse simultaneously to 1 and 2 channel - in this way can be maintained up to 16 different coins.
-====Бутони====
+====Buttons====
-Свързването на бутоните се осъществява с шест сигнални линии и обща маса. Допуска се свързването на нормално отворени и нормално затворени бутони, както и ключове.\\
+The connection of the buttons is carried out with 6 signal lines and common ground. The connection of normally open and normally closed buttons, as well as keys is allowed.\\
-При необходимост от повече бутони, чрез използването на разделителни диоди е възможно един бутон да управлява няколко сигнални линии. По този начин е възможно свързването до 16 бутона за програми и ключ оператор.
+If more buttons are necessary:
+ By using separation diodes it is possible for one button to control several signal lines. In this way, it is possible to connect up to 16 buttons for programs and operator's key.
 {{ ::cw01r66_buttons_diagram.png?nolink |}}
-====Примерна пълна схема====
+====Complete scheme example ====
-Това е схема на изградена автомивка с 4 програми.
+This is a scheme of a built carwash with 4 programs.
 {{ ::cw01r66_4programs_circuit.png?direct&800 |}}
-Използват се следните управляващи сигнали:
+The  following controlling signals are used:
-  * Реле 1 - главен клапан за пускане на водата
+  * Relay 1 - main valve for water release
-  * Реле 2 - компресор за високо налягане
+  * Relay 2 - compressor for high pressure
-  * Реле 3 - дозатор да препарат
+  * Relay 3 - detergent dispenser
-  * Реле 4 - дозатор за вакса
+  * Relay 4 - wax dispenser
-За контролера е необходимо да се направят следните настройки на програмите:
+The following settings for the programs need to be made for the  controller
-^ N ^ Програма ^ Изходи ^
+^ N ^ Program ^ relay ^
-| 1 | Водоструйка | 1 + 2 |
+| 1 | Water jet | 1 + 2 |
-| 2 | Препарат - ниско налягане | 1 + 3 |
+| 2 | Detergent - low pressure | 1 + 3 |
-| 3 | Препарат - високо налягане (пяна)| 1 + 2 + 3 |
+| 3 | Detergent - high pressure (foam)| 1 + 2 + 3 |
-| 4 | Вакса | 1 + 4 |
+| 4 | Wax | 1 + 4 |